Kontron AT8904 CLI Bedienungsanleitung Seite 251
- Seite / 317
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AT8904M Utility Commands
Page 5 - 51 AT8904M CLI Reference Manual
Type Type determines whether or not the ICMP message is a
REQUEST or a RESPONSE.
5.11.9.1 no debug ping packet
This command disables tracing of ICMP echo requests and responses.
Format
no debug ping packet
Mode Privileged EXEC
5.11.10 debug rip packet
This command turns on tracing of RIP requests and responses. This command takes no
options. The output is directed to the log file.
Default
disabled
Format debug rip packet
Mode Privileged EXEC
A sample output of the trace message is shown below.
<15> JAN 01 00:35:15 192.168.17.29-1 RIP[181783160]:
rip_map_debug.c(96) 775 %
Pkt RX on Intf: 1/0/1(1), Src_IP:43.1.1.1 Dest_IP:43.1.1.2
Rip_Version: RIPv2 Packet_Type:RIP_RESPONSE
ROUTE 1): Network: 10.1.1.0 Mask: 255.255.255.0 Metric: 1
ROUTE 2): Network: 40.1.0.0 Mask: 255.255.0.0 Metric: 1
ROUTE 3): Network: 10.50.50.0 Mask: 255.255.255.0 Metric: 1
ROUTE 4): Network: 41.1.0.0 Mask: 255.255.0.0 Metric: 1
ROUTE 5): Network:42.0.0.0 Mask:255.0.0.0 Metric:1
Another 6 routes present in packet not displayed.
The following parameters are displayed in the trace message:
TX/RX
TX refers to a packet transmitted by the device. RX refers
to packets received by the device.
Intf The interface that the packet came in or went out on. For-
mat used is slot/port (internal interface number).
Src_IP The source IP address in the IP header of the packet.
Dest_IP The destination IP address in the IP header of the packet.
Rip_Version RIP version used <RIPv1 or RIPv2>.
Packet_Type Type of RIP packet. <RIP_REQUEST or RIP_RESPONSE>.
Routes Up to 5 routes in the packet are displayed in the follow-
ing format:
Network: <a.b.c.d> Mask <a.b.c.d> Next_Hop <a.b.c.d> Met-
ric <a>
The next hop is only displayed if it is different from
0.0.0.0.
For RIPv1 packets, Mask is always 0.0.0.0.
Number of routes not printed Only the first five routes present in the
packet are included in the trace. There is another notifi-
cation of the number of additional routes present in the
packet that were not included in the trace.
- AT8904M CLI Reference Manual 1
- AdvancedTCA 1
- AT8904M Preface 2
- Table of Contents 3
- Table of Contents AT8904M 10
- AT8904M Table of Contents 11
- Appendix 19
- Preface AT8904M 22
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.2.1 Common Parameter Values 29
- 1.5 Command Modes 31
- 1.5.2 CLI Error Messages 34
- 1.6 Using CLI Help 35
- 1.7 Accessing the CLI 36
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8904M 100
- AT8904M Switching Commands 101
- Routing Commands 115
- Chapter 1 115
- 3. Routing Commands 116
- AT8904M Routing Commands 117
- Routing Commands AT8904M 118
- Quality of Service Commands 169
- 4.1.3 classofservice trust 171
- [<slot/port>] 174
- 4.2.1 diffserv 175
- 4.3 DiffServ Class Commands 176
- 4.3.2 class-map rename 177
- 4.3.3 match ethertype 177
- 4.3.4 match any 177
- 4.3.5 match class-map 177
- 4.3.5.1 no match class-map 178
- 4.3.6 match cos 178
- 4.3.7 match secondary-cos 178
- 4.3.9 match dstip 179
- 4.3.10 match dstl4port 179
- 4.3.11 match ip dscp 179
- 4.3.12 match ip precedence 179
- 4.3.13 match ip tos 180
- 4.3.14 match protocol 180
- 4.3.16 match srcip 181
- 4.3.17 match srcl4port 181
- 4.3.18 match vlan 181
- 4.4 DiffServ Policy Commands 182
- 4.4.2 drop 183
- 4.4.3 mirror 183
- 4.4.4 redirect 183
- 4.4.5 conform-color 183
- 4.4.6 class 183
- 4.4.6.1 no class 184
- 4.4.7 mark cos 184
- 4.4.8 mark ip-dscp 184
- 4.4.9 mark ip-precedence 184
- 4.4.10 police-simple 185
- 4.4.11 policy-map 185
- 4.4.11.1 no policy-map 185
- 4.5 DiffServ Service Commands 186
- 4.6 DiffServ Show Commands 187
- 4.6.2 show diffserv 188
- 4.6.3 show policy-map 188
- 4.6.4 show diffserv service 190
- 4.6.7 show service-policy 191
- 4.7.3 {deny 192
- 4.7.4 mac access-group 194
- 4.7.4.1 no mac access-group 194
- 4.7.5 show mac access-lists 194
- 4.8.1 access-list 195
- 4.8.1.1 no access-list 196
- 4.8.2 ip access-group 197
- 4.8.2.1 no ip access-group 197
- 4.8.3 acl-trapflags 197
- 4.8.3.1 no acl-trapflags 197
- 4.8.4 show ip access-lists 197
- 4.8.5 show access-lists 198
- 4.9 ACL trap commands 199
- Utility Commands 201
- 5. Utility Commands 202
- AT8904M Utility Commands 203
- Utility Commands AT8904M 204
- Management Commands 255
- 6. Management Commands 256
- AT8904M Management Commands 257
- Management Commands AT8904M 258
- Getting Help 291
- A. Getting Help 292
- AT8904M Getting Help 293
- Getting Help AT8904M 294
- (if not under warranty) 295
- List of Commands 297
- B. List of Commands 298
- AT8904M List of Commands 299
- List of Commands AT8904M 300
Verwandte Produkte und Handbücher für Hardware Kontron AT8904 CLI
Hardware Kontron AT8940 Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Hardware Kontron RTM8940 Bedienungsanleitung
(36 Seiten)
(36 Seiten)
Hardware Kontron AT8402 CLI Bedienungsanleitung
(253 Seiten)
(253 Seiten)
Hardware Kontron AT8404 Bedienungsanleitung
(132 Seiten)
(132 Seiten)
Hardware Kontron AT8404 CLI Bedienungsanleitung
(373 Seiten)
(373 Seiten)
Hardware Kontron RTM8050 Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Hardware Kontron AT8050 Bedienungsanleitung
(165 Seiten)
(165 Seiten)
Hardware Kontron RTM8242 Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Hardware Kontron AT8242 Bedienungsanleitung
(109 Seiten)
(109 Seiten)
Hardware Kontron AT8060 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
Hardware Kontron RTM806x Bedienungsanleitung
(40 Seiten)
(40 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern