Kontron NSW1U IP Network Server Bedienungsanleitung Seite 70
- Seite / 110
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
NSW1U Network Server—Server Component Replacements
Kontron IP Network Server NSW1U
Product Guide, rev. 1.4 December 2009
70
5.3.2 Replacing the Light Pipes
Light pipe replacement instructions are included as part of the instructions for replacing the EFP
board. To transfer the light pipe assembly from EFP board just removed, use the procedures that
follow.
To replace the light pipes on the existing EFP board when you are not installing a replacement EFP
board, you still need to follow the same procedures:
• “Removing the Ethernet Front Panel (EFP) Board”
• “Replacing the Light Pipes” (the steps below)
• “Installing the EFP Board”
1. Note the position of the light pipes so that you will be able to correctly position the assembly on
the EFP board during the re-installation process. The pipes extend outward from the EFP board to
the front panel control panel.
2. Remove the light pipe assembly by gently pressing the four plastic clips from the underside of the
EFP board until the bottom of the clips are flush with the bottom of the EFP board.
3. Gently ease the light pipes from the EFP board.
4. Insert the four plastic clips on the light pipe assembly or the replacement light pipes into the
matching holes in the new EFP board. Insert the clips gently and evenly—do not insert one clip
fully without first partially pressing the others into place.
5.3.3 Installing the EFP Board
1. Lower the replacement EFP board into the chassis.
2. While holding the rear edge of the board, ease the board forward, sliding the NIC connector
(NSW1U-F and NSW1U-B) and USB port through the matching cutout at the front panel of the
chassis.
3. Lower the rear of the board into position, fitting the board over the placement pegs. (Figure 54,
“A”)
4. Push the board forward, locking the board onto the placement pegs. (“B”)
5. Replace the screws you removed previously. (“C”)
6. Reinstall the PCI fan assembly. For instructions see Section 5.2.4, “Installing the PCI Fan” on
page 67.
7. Reinstall the eUSB SSD if you are using it. For instructions see Section 4.7, “Installing a SMART
Embedded USB Solid-State Drive” on page 61.
8. Reconnect all of the cables that were disconnected when removing the old EFP board:
• All fan power cables (3 CPU/memory fans and PCI fan)
•Flex cable
• Optical device power cable
• SATA hard drive connectors
• eUSB solid-state drive cable, if installed
• 4xGbE LAN card cables, if installed
• Power interconnect to PDB
9. If this is the last task you are performing, replace the top cover of the chassis. Reconnect all the
external devices and plug in the power cord(s).
- Product Guide 1
- Rev. 1.4 1
- Contents 3
- NSW1U Network Server—Contents 4
- Contents—NSW1U Network Server 5
- Revision History 7
- 1 Introduction 9
- 1.3 Product Accessories 10
- •System drivers 11
- • Firmware and BIOS updates 11
- 2.1 Server Components 14
- 2.2 Back Panel 15
- 2.3 NSW1U Server Front Panels 16
- AF000816rev3 17
- AF000817rev 18
- AF000818 19
- 2.5.1 Front Panel Features 20
- AF000750 21
- 2.8 Hard Disk Drives 22
- 2.9 Riser Card Assembly 22
- 2.10 Power Supply 22
- 2.11 System Cooling 22
- AF000830 23
- 2.12 Hardware Requirements 24
- 3.1 Before You Begin 25
- AF000876rev 26
- AF000875 27
- AF000880 28
- 3.3.1.1 Jumper Blocks 29
- 3.3.1.4 BIOS Select Jumper 30
- DIMM Sockets 32
- 3.3.3.1 Installing DIMMs 34
- AF000775 35
- 19, “A” and “B”) 37
- AF000769 38
- AF000770 38
- AF000773 39
- AF000877 41
- 4.1 Before You Begin 45
- AF000820 48
- TS000407 49
- TS000409 50
- TS000410 51
- TS000411 52
- TS000213 53
- TS000214 54
- 4.5.2 Installing the RMM2 55
- GCM3 ModuleRMM Module 56
- AF000884 57
- AF000887 58
- AF000888 59
- AF000886 60
- TS000504 61
- TS000505 62
- TS000506 62
- TS000507 63
- TS000508 64
- 5.1 Before You Begin 65
- TS000404 66
- TS000405 67
- TS000406 68
- AF000896 69
- AF000897 71
- AF000894 72
- AF000895 72
- AF000898 74
- AF000899 75
- TS000416 77
- TS000417 78
- 5.6.2 Running Setup 79
- 6 Server Utilities 80
- 6.2 Updating the BIOS 81
- Yes] [NO] 81
- 6.2.1.2 Obtaining the Update 82
- 6.3 Clearing the CMOS 82
- 6.4 Clearing the Password 83
- 7 Troubleshooting 84
- 7.5 LED Information 89
- 7.6 BIOS Error Messages 90
- 7.6.1 BIOS POST Beep Codes 91
- Table 11. BMC Beep Codes 92
- 8 Warranty 93
- A.1 Emissions Disclaimer 94
- A.2 Intended Uses 94
- A.3 Safety Cautions 96
- Wichtige Sicherheitshinweise 97
- Consignes de sécurité 99
- B.2.1 FCC (USA) 106
- B.2.4 VCCI (Japan) 107
- B.2.5 BSMI (Taiwan) 107
- B.2.6 Korean RRL Compliance 108
- Appendix C: Getting Help 109
Verwandte Produkte und Handbücher für Computerhardware Kontron NSW1U IP Network Server
(9 Seiten)
(49 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern