Kontron AT890X Full-Size CLI Bedienungsanleitung Seite 117
- Seite / 304
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AT8901/2/3 Routing Commands
Page 3 - 5 AT8901/2/3 CLI Reference Manual
Mode Global Config
3.1.8.1 no arp timeout
This command configures the default ARP entry ageout time.
Format
no arp timeout
Mode Global Config
3.1.9 clear arp-cache
This command causes all ARP entries of type dynamic to be removed from the ARP
cache. If the gateway keyword is specified, the dynamic entries of type gateway are
purged as well.
Format
clear arp-cache [gateway]
Mode Privileged EXEC
3.1.10 show arp
This command displays the Address Resolution Protocol (ARP) cache. The displayed
results are not the total ARP entries. To view the total ARP entries, the operator should
view the
show arp results in conjunction with the show arp switch results.
Format
show arp
Mode Privileged EXEC
Age Time (seconds) Is the time it takes for an ARP entry to age out. This value was
configured into the unit. Age time is measured in seconds.
Response Time (seconds) Is the time it takes for an ARP request timeout. This value
was configured into the unit. Response time is measured in seconds.
Retries Is the maximum number of times an ARP request is retried. This value
was configured into the unit.
Cache Size Is the maximum number of entries in the ARP table. This value was
configured into the unit.
Dynamic Renew Mode Displays whether the ARP component automatically attempts
to renew dynamic ARP entries when they age out.
Total Entry Count Current / Peak Field listing the total entries in the ARP table and
the peak entry count in the ARP table.
Static Entry Count Current / Max Field listing the static entry count in the ARP
table and maximum static entry count in the ARP table.
The following are displayed for each ARP entry.
IP Address Is the IP address of a device on a subnet attached to an existing routing
interface.
MAC Address Is the hardware MAC address of that device.
Interface Is the routing unit/slot/port associated with the device ARP entry.
- AdvancedTCA 1
- AT8901/2/3 Preface 2
- Preface AT8901/2/3 4
- AT8901/2/3 10
- Appendix 24
- 1.1 Command Syntax 26
- 1.2 Command Conventions 26
- 1.2.1 Common Parameter Values 27
- 1.5 Command Modes 29
- 1.5.2 CLI Error Messages 32
- 1.6 Using CLI Help 33
- 1.7 Accessing the CLI 34
- Switching Commands 35
- 2. Switching Commands 36
- Switching Commands AT8901/2/3 100
- AT8901/2/3 Switching Commands 101
- Routing Commands 113
- Chapter 1 113
- 3. Routing Commands 114
- AT8901/2/3 Routing Commands 115
- Routing Commands AT8901/2/3 116
- Quality of Service Commands 167
- 4.1.4 classofservice trust 169
- 4.1.5 cos-queue min-bandwidth 170
- 4.1.6 cos-queue strict 170
- 4.1.6.1 no cos-queue strict 170
- 4.1.7 traffic-shape 171
- 4.1.7.1 no traffic-shape 171
- Mode Privileged EXEC 172
- [<unit/slot/port>] 172
- 4.3 DiffServ Class Commands 174
- 4.3.1.1 no class-map 175
- 4.3.2 class-map rename 175
- 4.3.3 match ethertype 175
- 4.3.4 match any 175
- 4.3.5 match class-map 175
- 4.3.5.1 no match class-map 176
- 4.3.6 match cos 176
- 4.3.7 match secondary-cos 176
- 4.3.9 match dstip 177
- 4.3.10 match dstl4port 177
- 4.3.11 match ip dscp 177
- 4.3.12 match ip precedence 178
- 4.3.13 match ip tos 178
- 4.3.14 match protocol 178
- 4.3.16 match srcip 179
- 4.3.17 match srcl4port 179
- 4.4 DiffServ Policy Commands 180
- 4.4.1 assign-queue 181
- 4.4.2 drop 181
- 4.4.3 mirror 181
- 4.4.4 redirect 181
- 4.4.5 conform-color 181
- 4.4.6 class 182
- 4.4.6.1 no class 182
- 4.4.7 mark cos 182
- 4.4.8 mark ip-dscp 182
- 4.4.9 mark ip-precedence 183
- 4.4.10 police-simple 183
- 4.4.11 policy-map 183
- 4.5 DiffServ Service Commands 184
- 4.6 DiffServ Show Commands 185
- 4.6.2 show diffserv 186
- 4.6.3 show policy-map 186
- 4.6.4 show diffserv service 188
- 4.6.7 show service-policy 189
- 4.7.3 {deny 191
- 4.7.4 mac access-group 192
- 4.7.4.1 no mac access-group 192
- 4.7.5 show mac access-lists 192
- 4.8.1 access-list 193
- 4.8.1.1 no access-list 195
- 4.8.2 ip access-group 195
- 4.8.2.1 no ip access-group 195
- 4.8.3 acl-trapflags 195
- 4.8.3.1 no acl-trapflags 196
- 4.8.4 show ip access-lists 196
- 4.8.5 show access-lists 197
- Utility Commands 199
- 5. Utility Commands 200
- AT8901/2/3 Utility Commands 201
- Utility Commands AT8901/2/3 202
- Management Commands 243
- 6. Management Commands 244
- 6.1.3 serviceport protocol 245
- 6.1.4 network parms 245
- 6.1.5 network protocol 245
- 6.1.6 network mac-address 245
- 6.1.7 network mac-type 245
- 6.1.7.1 no network mac-type 246
- 6.1.8 network javamode 246
- 6.1.8.1 no network javamode 246
- 6.1.9 show network 246
- 6.1.10 show serviceport 247
- 6.2.1 configuration 247
- 6.3 Telnet Commands 249
- 6.3.3 transport input telnet 250
- 6.3.4 transport output telnet 250
- 6.3.5 session-limit 250
- 6.3.8.1 no telnetcon timeout 252
- 6.3.9 disconnect 252
- 6.3.10 show telnet 252
- 6.3.11 show telnetcon 252
- 6.4.1 ip ssh 253
- 6.4.1.1 no ip ssh 253
- 6.4.2 ip ssh protocol 253
- 6.4.3 ip ssh server enable 253
- 6.5 User Account Commands 255
- 6.5.3 users snmpv3 accessmode 256
- 6.5.2.1 no users passwd 256
- 6.5.5 users snmpv3 encryption 257
- 6.5.6 show loginsession 257
- 6.6 SNMP Commands 258
- 6.6.3 snmp-server community 259
- 6.6.15 snmptrap 263
- 6.6.15.1 no snmptrap 263
- 6.6.16 snmptrap snmpversion 263
- 6.6.17 snmptrap ipaddr 263
- 6.6.21 show snmpbind 265
- 6.6.22 show snmpcommunity 265
- 6.6.23 show snmptrap 265
- 6.6.24 show trapflags 266
- 6.8 RADIUS Commands 267
- 6.8.2.1 no radius server host 268
- 6.8.3 radius server key 268
- 6.8.4 radius server msgauth 268
- 6.8.5 radius server primary 269
- 6.8.7 radius server timeout 269
- 6.8.8 show radius 270
- 6.8.9 show radius accounting 270
- 6.8.10 show radius statistics 271
- 6.9 TACACS+ Commands 272
- 6.10.1 script apply 275
- 6.10.3 script delete 276
- 6.10.4 script list 276
- 6.10.5 script show 276
- 6.10.6 script validate 276
- 6.12 Watchdog support 277
- 6.13 ASI commands 278
- Getting Help 279
- A. Getting Help 280
- AT8901/2/3 Getting Help 281
- Getting Help AT8901/2/3 282
- (if not under warranty) 283
- List of Commands 285
- B. List of Commands 286
- AT8901/2/3 List of Commands 287
- List of Commands AT8901/2/3 288
Verwandte Produkte und Handbücher für Hardware Kontron AT890X Full-Size CLI
(9 Seiten)
Hardware Kontron AT8901 Bedienungsanleitung
(79 Seiten)
(79 Seiten)
Hardware Kontron AT8901M Bedienungsanleitung
(76 Seiten)
(76 Seiten)
Hardware Kontron AT8901M CLI Bedienungsanleitung
(313 Seiten)
(313 Seiten)
Hardware Kontron AT8902 Bedienungsanleitung
(94 Seiten)
(94 Seiten)
Hardware Kontron AT8902M Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Hardware Kontron AT8902M CLI Bedienungsanleitung
(315 Seiten)
(315 Seiten)
Hardware Kontron AT8904 Bedienungsanleitung
(93 Seiten)
(93 Seiten)
Hardware Kontron AT8904 CLI Bedienungsanleitung
(317 Seiten)
(317 Seiten)
Hardware Kontron AT8940 Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Hardware Kontron RTM8940 Bedienungsanleitung
(36 Seiten)
(36 Seiten)
Hardware Kontron AT8402 CLI Bedienungsanleitung
(253 Seiten)
(253 Seiten)
Hardware Kontron AT8404 Bedienungsanleitung
(132 Seiten)
(132 Seiten)
Hardware Kontron AT8404 CLI Bedienungsanleitung
(373 Seiten)
(373 Seiten)
Hardware Kontron RTM8050 Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Hardware Kontron AT8050 Bedienungsanleitung
(165 Seiten)
(165 Seiten)
Hardware Kontron RTM8242 Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Harbor Freight Tools 15 lb. Portable Soda Blaster manuály
Uživatelské manuály a uživatelské příručky pro Elektrické nářadí Harbor Freight Tools 15 lb. Portable Soda Blaster.
Poskytujeme 1 manuály pdf Harbor Freight Tools 15 lb. Portable Soda Blaster ke stažení zdarma podle typů dokumentů: Manuál
Kommentare zu diesen Handbüchern