Kontron KTGM45-mITX Bedienungsanleitung PDF herunterladen (Seite 16)

100

101

KTGM45 Users Guide

KTD-N0793-O Page 16

2.4 System Memory support

The KTGM45 board has two DDR3 DIMM sockets and support the following memory features:

• 1.5V (only) 240-pin DDR3 SDRAM DIMMs with gold-plated contacts

• DDR3-800 (PC3-6400) and DDR3-1066 (PC3-8500)

• DDR3-800/1066 DIMM with SPD timings supported

• Unbuffered, single-sided x8/x16 or double-sided x8/x16 DIMMs

• Supports one or two rank populated DIMM’s.

• 8GB (2x 4GB) max. total system memory using 64-bit OS. (Shared Video Memory is subtracted).

• 4GB maximum total system memory using 32-bit OS. ~3GB is displayed in System Properties.

(Shared Video Memory is subtracted).

• Minimum total system memory: 512 MB

• Non-ECC DIMMs

The installed DDR3 SDRAM should support the Serial Presence Detect (SPD) data structure. This allows the

BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is used, the

BIOS will attempt to configure the memory settings, but performance and reliability may be impacted.

Memory Operating Frequencies

Regardless of the DIMM type used, the memory frequency will either be equal to or less than the processor

system bus frequency. For example, if DDR3 800 memory is used with an 800 MHz system bus frequency

processor, the memory clock will operate at 400 MHz. The table below lists the resulting operating memory

frequencies based on the combination of DIMMs and processors.

DIMM Type

Module

name

Memory

Data

transfers

[Mill/s]

Processor

system bus

frequency

[MHz]

Resulting

memory clock

frequency

[MHz]

Peak transfer

rate

[MB/s]

DDR3 800

PC3-6400

800

667

333

5300

DDR3 800

PC3-6400

800

400

6400

DDR3 800

PC3-6400

800

1066

400

6400

DDR3 1066

PC3-8500

1066

667

333

5300

DDR3 1066

PC3-8500

1066

800

400

6400

DDR3 1066

PC3-8500

1066

533

8533

Notes: Kontron offers the following memory modules:

• P/N 1028-6891, DDR3-RAM, 1GB, 240p, 1066MHZ, PC3-8500, DIMM

• P/N 1030-5722, DDR3-RAM, 1GB, 240p, 1333MHZ, PC3-10600, DIMM

• P/N 1030-5747, DDR3-RAM, 2GB, 240p, 1066MHZ, PC3-8500, DIMM

• P/N 1028-6892, DDR3-RAM, 2GB, 240p, 1333MHZ, PC3-10600, DIMM

• P/N 825534, DDR3-RAM, 4GB, 240P, 1333MHZ, PC3-10600, DIMM

• Faster RAM than PC3-10600 can be used but will run at lower speed.

Memory Configurations

The KTGM45 boards support the following three types of memory organization:

1. Dual channel (Interleaved) mode

. This mode offers the highest throughput. Dual channel mode is enabled

when the installed memory capacities of both DIMM channels are equal. Technology and device width can

vary from one channel to the other but the installed memory capacity for each channel must be equal. If

different speeds DIMMs are used between channels, the slowest memory timing will be used.

2. Single channel (Asymmetric) mode

. This mode is equivalent to single channel bandwidth operation. This

mode is used when only a single DIMM is installed or the memory capacities of channel A is bigger than of

channel B. Technology and device width can vary from one channel to the other. If different speeds DIMMs

are used between channels, the slowest memory timing will be used.

3. Flex mode.

This mode provides the most flexible performance characteristics and is used if both channels

are populated and at the same time the memory capacities of channel A is smaller than of channel B.

Channel B will be divided into two parts. One part of channel B is used together with channel A and mapped

to dual channel operation. The second part of channel B is mapped to single channel operation.

System specification

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 100 101

Kommentare zu diesen Handbüchern

Keine Kommentare

Kontron KTGM45-mITX Bedienungsanleitung Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Kontron KTGM45-mITX