Kontron AT8404 CLI Bedienungsanleitung Seite 138
- Seite / 373
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Switching Commands AT8404
AT8404 CLI Reference Manual Page 2 - 102
2.19.6 show igmpsnooping querier
Use this command to display IGMP Snooping Querier information. Configured information is displayed whether or
not IGMP Snooping Querier is enabled.
When the optional argument <vlanid> is not used, the command displays the following information.
When you specify a value for <vlanid>, the following additional information appears.
When the optional argument detail is used, the command shows the global information and the information for all
Querier-enabled VLANs.
2.20 MLD Snooping Commands
This section describes commands used for MLD Snooping. In IPv4, Layer 2 switches can use IGMP Snooping to
limit the flooding of multicast traffic by dynamically configuring Layer 2 interfaces so that multicast traffic is forwarded
only to those interfaces associated with IP multicast addresses. In IPv6, MLD Snooping performs a similar function.
With MLD Snooping, IPv6 multicast data is selectively forwarded to a list of ports that want to receive the data,
instead of being flooded to all ports in a VLAN. This list is constructed by snooping IPv6 multicast control packets.
Format show igmpsnooping querier [{detail | vlan <vlanid>}]
Mode Privileged EXEC
Field Description
Admin Mode Indicates whether or not IGMP Snooping Querier is active on the switch.
Admin Version The version of IGMP that will be used while sending out the queries.
Querier Address The IP Address which will be used in the IPv4 header while sending out IGMP queries. It can
be configured using the appropriate command.
Query Interval The amount of time in seconds that a Snooping Querier waits before sending out the periodic
general query.
Querier Timeout The amount of time to wait in the Non-Querier operational state before moving to a Querier
state.
Field Description
VLAN Admin Mode Indicates whether iGMP Snooping Querier is active on the VLAN.
VLAN Operational
State
Indicates whether IGMP Snooping Querier is in “Querier” or “Non-Querier” state. When the
switch is in Querier state, it will send out periodic general queries. When in Non-Querier
state, it will wait for moving to Querier state and does not send out any queries.
VLAN Operational
Max Response
Time
Indicates the time to wait before removing a Leave from a host upon receiving a Leave
request. This value is calculated dynamically from the Queries received from the network. If
the Snooping Switch is in Querier state, then it is equal to the configured value.
Querier Election
Participation
Indicates whether the IGMP Snooping Querier participates in querier election if it discovers
the presence of a querier in the VLAN.
Querier VLAN
Address
The IP address will be used in the IPv4 header while sending out IGMP queries on this VLAN.
It can be configured using the appropriate command.
Operational
Version
The version of IPv4 will be used while sending out IGMP queries on this VLAN.
Last Querier
Address
Indicates the IP address of the most recent Querier from which a Query was received.
Last Querier
Version
Indicates the IGMP version of the most recent Querier from which a Query was received on
this VLAN.
- AT8404 CLI Reference Manual 1
- AdvancedTCA 1
- Revision History 2
- Disclaimer 2
- AT8404 Preface 3
- About This Book 3
- Proprietary Note 3
- Trademarks 3
- Preface AT8404 4
- Explanation of Symbols 4
- For Your Safety 4
- Two Year Warranty 5
- Appendix 25
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.3 Common Parameter Values 29
- 1.6 FASTPATH Modules 30
- 1.7 Command Modes 31
- 1.9 CLI Error Messages 33
- 1.11 Using CLI Help 34
- 1.12 Accessing the CLI 34
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8404 100
- AT8404 Switching Commands 101
- Quality of Service Commands 175
- Chapter 1 175
- -mapping 176
- 3.1.3 classofservice trust 177
- 3.1.4 cos-queue min-bandwidth 177
- 3.1.13 show packet-memory 180
- 3.1.16 show protection-group 181
- Mode Global Config 183
- 3.3.1 class-map 184
- 3.3.1.1 no class-map 184
- 3.3.2 class-map rename 184
- 3.3.3 match ethertype 184
- 3.3.4 match any 185
- 3.3.5 match class-map 185
- 3.3.5.1 no match class-map 186
- 3.3.6 match cos 186
- 3.3.7 match secondary-cos 186
- 3.3.9 match dstip 187
- 3.3.10 match dstip6 187
- 3.3.11 match dstl4port 187
- 3.3.12 match ip dscp 187
- 3.3.13 match ip precedence 188
- 3.3.14 match ip tos 188
- 3.3.15 match protocol 189
- 3.3.17 match srcip 189
- 3.3.18 match srcip6 190
- 3.3.19 match srcl4port 190
- 3.3.20 match vlan 190
- 3.3.21 match secondary-vlan 190
- 3.4 DiffServ Policy Commands 191
- 3.4.4 redirect 192
- 3.4.5 conform-color 192
- 3.4.6 class 192
- 3.4.6.1 no class 193
- 3.4.7 mark cos 193
- 3.4.8 mark ip-precedence 193
- 3.4.9 police-simple 194
- 3.4.10 policy-map 194
- 3.4.10.1 no policy-map 194
- 3.5 DiffServ Service Commands 195
- 3.6 DiffServ Show Commands 196
- Mode Privileged EXEC 197
- <slot/port> in 199
- 3.6.7 show service-policy 200
- 3.7.4 mac access-group 203
- 3.7.4.1 no mac access-group 203
- 3.7.5 show mac access-lists 203
- 3.8.1 access-list 204
- 3.8.1.1 no access-list 205
- 3.8.2 ip access-list 205
- 3.8.2.1 no ip access-list 206
- 3.8.3 ip access-list rename 206
- 3.8.5 ip access-group 207
- 3.8.5.1 no ip access-group 207
- 3.8.6 acl-trapflags 207
- 3.8.6.1 no acl-trapflags 207
- 3.8.7 show acl-traptimer 208
- 3.8.8 acl-traptimer 208
- 3.8.8.1 no acl-traptimer 208
- 3.8.9 show ip access-lists 208
- 3.8.10 show access-lists 209
- 3.9.1 ipv6 access-list 209
- 3.9.1.1 no ipv6 access-list 210
- 3.9.2 ipv6 access-list rename 210
- 3.9.3 {deny 210
- 3.9.4 ipv6 traffic-filter 211
- 3.9.5 show ipv6 access-lists 211
- 3.10.1 auto-voip all 212
- 3.10.1.1 no auto-voip all 212
- 3.10.2 auto-voip 213
- 3.10.2.1 no auto-voip 213
- 3.10.3 show auto-voip 213
- Utility Commands 215
- 4. Utility Commands 216
- AT8404 Utility Commands 217
- Utility Commands AT8404 218
- Management Commands 277
- 5. Management Commands 278
- AT8404 Management Commands 279
- Management Commands AT8404 280
- Getting Help 329
- A. Getting Help 330
- AT8404 Getting Help 331
- FASTPATH log messages 334
- B. FASTPATH Log Messages 335
- AT8404 FASTPATH log messages 336
- FASTPATH log messages AT8404 337
- List of Commands 350
- C. List of Commands 351
- .......3 - 9 352
- List of Commands AT8404 353
- AT8404 List of Commands 354
Verwandte Produkte und Handbücher für Hardware Kontron AT8404 CLI
Hardware Kontron RTM8050 Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Hardware Kontron AT8050 Bedienungsanleitung
(165 Seiten)
(165 Seiten)
Hardware Kontron RTM8242 Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Hardware Kontron AT8242 Bedienungsanleitung
(109 Seiten)
(109 Seiten)
Hardware Kontron AT8060 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
Hardware Kontron RTM806x Bedienungsanleitung
(40 Seiten)
(40 Seiten)
Hardware Kontron KTGM45-mITX Bedienungsanleitung
(101 Seiten)
(101 Seiten)
Hardware Kontron KTQ45-FLEX Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Hardware Kontron KTQM67-mITX Bedienungsanleitung
(148 Seiten)
(148 Seiten)
Hardware Kontron KTQ67-FLEX Bedienungsanleitung
(137 Seiten)
(137 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern