Kontron AT8404 CLI Bedienungsanleitung PDF herunterladen (Seite 348)

AT8404 FASTPATH log messages

Page B - 15 AT8404 CLI Reference Manual

Table 36: Linux BSP Log Message

Component Message Cause

Linux BSP rc = 10 Second message logged at bootup, right after

“Starting code…”. Always logged.

Table 37: OSAPI Linux Log Messages

Component Message Cause

OSAPI Linux osapiNetLinkNeighDump: could not open

socket! - or –

ipstkNdpFlush: could not open socket! – or –

osapiNetlinkDumpOpen: unable to bind

socket! errno = XX

Couldn’t open a “netlink” socket. Make sure

“ARP Daemon support” (CONFIG_ARPD) is

enabled in the Linux kernel, if the

BROADCOM reference kernel binary is not

being used.

OSAPI Linux ipstkNdpFlush: sending delete failed Failed when telling the kernel to delete a

neighbor table entry (the message is

incorrect)

OSAPI Linux unable to open /proc/net/ipv6/conf/default/

hop_limit

IPv6 MIB objects read, but /proc filesystem is

not mounted, or running kernel does not have

IPV6 support

OSAPI Linux osapimRouteEntryAdd, errno XX adding 0xYY

to ZZ – or –

osapimRouteEntryDelete, errno XX deleting

0xYY from ZZ

Error adding or deleting an IPv4 route (listed in

hex as YY), on the interface with Linux name

ZZ Error code can be looked up in errno.h.

OSAPI Linux l3intfAddRoute: Failed to Add Route – or –

l3intfDeleteRoute: Failed to Delete Route

Error adding or deleting a default gateway in

the kernel’s routing table (the function is really

osapiRawMRouteAdd()/Delete())

OSAPI Linux osapiNetIfConfig: ioctl on XX failed: addr:

0xYY, err: ZZ – or –

osapiNetIPSet: ioctl on XX failed: addr:

0x%YY

Failed trying to set the IP address (in hex as

YY) of the interface with Linux name XX, and

the interface does not exist. Sometimes this is

a harmless race condition (e.g. we try to set

address 0 when DHCPing on the network port

(dtl0) at bootup, before it’s created using

TAP).

OSAPI Linux ping: sendto error Trouble sending an ICMP echo request

packet for the UI ‘ping’ command. Maybe

there was no route to that network.

OSAPI Linux Failed to Create Interface Out of memory at system initialization time.

OSAPI Linux TAP Unable to open XX The /dev/tap file is missing, or, if not using the

BRPOADCOM reference kernel binary, the

kernel is missing “Universal TUN/TAP device

driver support” (CONFIG_TUN).

OSAPI Linux Tap monitor task is spinning on select failures

– then –

Tap monitor select failed: XX

Trouble reading the /dev/tap device, check the

error message XX for details.

OSAPI Linux Log_Init: log file error - creating new log file This pertains to the “event log” persistent file

in flash. Either it did not exist, or had a bad

checksum.

OSAPI Linux Log_Init: Flash (event) log full; erasing Event log file has been cleared; happens at

boot time.

OSAPI Linux Log_Init: Corrupt event log; erasing Event log file had a non-blank entry after a

blank entry; therefore, something was messed

up.

1 2 ... 343 344 345 346 347 348 349 350 351 352 353 ... 372 373

Kommentare zu diesen Handbüchern

Keine Kommentare

Kontron AT8404 CLI Bedienungsanleitung Seite 348

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Kontron AT8404 CLI