Kontron AT8404 CLI Bedienungsanleitung Seite 300
- Seite / 373
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Management Commands AT8404
AT8404 CLI Reference Manual Page 5 - 24
5.8.9 snmp-server enable traps linkmode
This command enables Link Up/Down traps for the entire switch. When enabled, link traps are sent only if the Link
Trap flag setting associated with the port is enabled. See “snmp trap link-status” on page 5 - 26.
5.8.9.1 no snmp-server enable traps linkmode
This command disables Link Up/Down traps for the entire switch.
5.8.10 snmp-server enable traps multiusers
This command enables Multiple User traps. When the traps are enabled, a Multiple User Trap is sent when a user
logs in to the terminal interface (EIA 232 or Telnet) and there is an existing terminal interface session.
5.8.10.1 no snmp-server enable traps multiusers
This command disables Multiple User traps.
5.8.11 snmp-server enable traps pll
This command enables the generation of traps in case a PLL status change has occurred.
5.8.11.1 no snmp-server enable traps pll
This command disables the generation of traps in case a PLL status change has occurred.
Note: This command may not be available on all platforms.
Default enabled
Format snmp-server enable traps linkmode
Mode Global Config
Format no snmp-server enable traps linkmode
Mode Global Config
Default enabled
Format snmp-server enable traps multiusers
Mode Global Config
Format no snmp-server enable traps multiusers
Mode Global Config
Default enabled
Format snmp-server enable traps pll
Mode Global Config
Format no snmp-server enable traps pll
Mode Global Config
- AT8404 CLI Reference Manual 1
- AdvancedTCA 1
- Revision History 2
- Disclaimer 2
- AT8404 Preface 3
- About This Book 3
- Proprietary Note 3
- Trademarks 3
- Preface AT8404 4
- Explanation of Symbols 4
- For Your Safety 4
- Two Year Warranty 5
- Appendix 25
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.3 Common Parameter Values 29
- 1.6 FASTPATH Modules 30
- 1.7 Command Modes 31
- 1.9 CLI Error Messages 33
- 1.11 Using CLI Help 34
- 1.12 Accessing the CLI 34
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8404 100
- AT8404 Switching Commands 101
- Quality of Service Commands 175
- Chapter 1 175
- -mapping 176
- 3.1.3 classofservice trust 177
- 3.1.4 cos-queue min-bandwidth 177
- 3.1.13 show packet-memory 180
- 3.1.16 show protection-group 181
- Mode Global Config 183
- 3.3.1 class-map 184
- 3.3.1.1 no class-map 184
- 3.3.2 class-map rename 184
- 3.3.3 match ethertype 184
- 3.3.4 match any 185
- 3.3.5 match class-map 185
- 3.3.5.1 no match class-map 186
- 3.3.6 match cos 186
- 3.3.7 match secondary-cos 186
- 3.3.9 match dstip 187
- 3.3.10 match dstip6 187
- 3.3.11 match dstl4port 187
- 3.3.12 match ip dscp 187
- 3.3.13 match ip precedence 188
- 3.3.14 match ip tos 188
- 3.3.15 match protocol 189
- 3.3.17 match srcip 189
- 3.3.18 match srcip6 190
- 3.3.19 match srcl4port 190
- 3.3.20 match vlan 190
- 3.3.21 match secondary-vlan 190
- 3.4 DiffServ Policy Commands 191
- 3.4.4 redirect 192
- 3.4.5 conform-color 192
- 3.4.6 class 192
- 3.4.6.1 no class 193
- 3.4.7 mark cos 193
- 3.4.8 mark ip-precedence 193
- 3.4.9 police-simple 194
- 3.4.10 policy-map 194
- 3.4.10.1 no policy-map 194
- 3.5 DiffServ Service Commands 195
- 3.6 DiffServ Show Commands 196
- Mode Privileged EXEC 197
- <slot/port> in 199
- 3.6.7 show service-policy 200
- 3.7.4 mac access-group 203
- 3.7.4.1 no mac access-group 203
- 3.7.5 show mac access-lists 203
- 3.8.1 access-list 204
- 3.8.1.1 no access-list 205
- 3.8.2 ip access-list 205
- 3.8.2.1 no ip access-list 206
- 3.8.3 ip access-list rename 206
- 3.8.5 ip access-group 207
- 3.8.5.1 no ip access-group 207
- 3.8.6 acl-trapflags 207
- 3.8.6.1 no acl-trapflags 207
- 3.8.7 show acl-traptimer 208
- 3.8.8 acl-traptimer 208
- 3.8.8.1 no acl-traptimer 208
- 3.8.9 show ip access-lists 208
- 3.8.10 show access-lists 209
- 3.9.1 ipv6 access-list 209
- 3.9.1.1 no ipv6 access-list 210
- 3.9.2 ipv6 access-list rename 210
- 3.9.3 {deny 210
- 3.9.4 ipv6 traffic-filter 211
- 3.9.5 show ipv6 access-lists 211
- 3.10.1 auto-voip all 212
- 3.10.1.1 no auto-voip all 212
- 3.10.2 auto-voip 213
- 3.10.2.1 no auto-voip 213
- 3.10.3 show auto-voip 213
- Utility Commands 215
- 4. Utility Commands 216
- AT8404 Utility Commands 217
- Utility Commands AT8404 218
- Management Commands 277
- 5. Management Commands 278
- AT8404 Management Commands 279
- Management Commands AT8404 280
- Getting Help 329
- A. Getting Help 330
- AT8404 Getting Help 331
- FASTPATH log messages 334
- B. FASTPATH Log Messages 335
- AT8404 FASTPATH log messages 336
- FASTPATH log messages AT8404 337
- List of Commands 350
- C. List of Commands 351
- .......3 - 9 352
- List of Commands AT8404 353
- AT8404 List of Commands 354
Verwandte Produkte und Handbücher für Hardware Kontron AT8404 CLI
Hardware Kontron RTM8050 Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Hardware Kontron AT8050 Bedienungsanleitung
(165 Seiten)
(165 Seiten)
Hardware Kontron RTM8242 Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Hardware Kontron AT8242 Bedienungsanleitung
(109 Seiten)
(109 Seiten)
Hardware Kontron AT8060 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
Hardware Kontron RTM806x Bedienungsanleitung
(40 Seiten)
(40 Seiten)
Hardware Kontron KTGM45-mITX Bedienungsanleitung
(101 Seiten)
(101 Seiten)
Hardware Kontron KTQ45-FLEX Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Hardware Kontron KTQM67-mITX Bedienungsanleitung
(148 Seiten)
(148 Seiten)
Hardware Kontron KTQ67-FLEX Bedienungsanleitung
(137 Seiten)
(137 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern